Estimated lead times
2-3 Days
Estimated lead times
2-3 Days
Lacquered low profile fasteners for internal and external liner panel systems, trims and flashing details, framework and ductwork.
Order information: Please call 0800 304 7616 if the colour you require is not available on the colour drop down. For some sizes or colours there may be a lead time, which is normally 2 working days. The delivery date will be shown on your order acknowledgement, or please call Customer Service if you wish to confirm before placing the order. A surcharge of £30 is applied for orders of less than 2000 fasteners per non stock colour.
- Wafer head
- Available from stock in 00E55 and RAL9010, for next-day delivery
- Can be powder coated to order in most RAL and BS colours as well as other brands and panel colours - available in 2-3 days
- For mechanically fixing metal sheeting systems to light metal purlins and rails
- For mechanically fixing components of steel and metal framing systems
|
Years / Environment
|
|||||||
|---|---|---|---|---|---|---|---|
| Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
| Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
| Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
|
Substrate
Steel
|
1.2 mm |
| Steel | |
| 0.5 mm | 1.91 kN |
| NR,II,K (Tensile - Pull-out) | 1.2mm Steel: 1.52 kN |
| 3mm Steel: 5.42 kN | |
| 5mm Steel: 10.76 kN |
|
Substrate
Steel
|
No washer |
| Steel | 5 mm |
| 0.5 mm | 3.98 kN |
| 0.7 mm | 4.52 kN |
| Installation tool | Variable speed electric screw gun |
| Installation drive | 2-PZD |
| Installation speed | 1500 RPM |
| Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
| Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
Lacquered low profile fasteners for internal and external liner panel systems, trims and flashing details, framework and ductwork.
Order information: Please call 0800 304 7616 if the colour you require is not available on the colour drop down. For some sizes or colours there may be a lead time, which is normally 2 working days. The delivery date will be shown on your order acknowledgement, or please call Customer Service if you wish to confirm before placing the order. A surcharge of £30 is applied for orders of less than 2000 fasteners per non stock colour.
- Wafer head
- Available from stock in 00E55 and RAL9010, for next-day delivery
- Can be powder coated to order in most RAL and BS colours as well as other brands and panel colours - available in 2-3 days
- For mechanically fixing metal sheeting systems to light metal purlins and rails
- For mechanically fixing components of steel and metal framing systems
|
Years / Environment
|
|||||||
|---|---|---|---|---|---|---|---|
| Interior | Semi-interior | Rural | Urban | Industrial / Coastal | Marine | Swimming pools & Chemical plants | |
| Corrosivity Category | C1 | - | C2 | C3 | C4 | C5 | - |
| Carbon steel case hardened | 25 | 20 | 12 | 0 | 0 | 0 | 0 |
|
Substrate
Steel
|
1.2 mm |
| Steel | |
| 0.5 mm | 1.91 kN |
| NR,II,K (Tensile - Pull-out) | 1.2mm Steel: 1.52 kN |
| 3mm Steel: 5.42 kN | |
| 5mm Steel: 10.76 kN |
|
Substrate
Steel
|
No washer |
| Steel | 5 mm |
| 0.5 mm | 3.98 kN |
| 0.7 mm | 4.52 kN |
| Installation tool | Variable speed electric screw gun |
| Installation drive | 2-PZD |
| Installation speed | 1500 RPM |
| Correct installation | Fasteners should be driven within three degrees of perpendicular to the surface of the fastened material. Use a depth-setting nosepiece to avoid over-driving, and do not over-tighten. Variants with bonded washers should not have the rubber compressed to less than two-thirds of its uncompressed height. Care should be taken when engaging and disengaging from the fastener head to avoid damage to the protective coating. |
| Handling | Fasteners may have sharp edges, and the use of power tools can be dangerous. Use personal protective equipment. Store fasteners in dry conditions. Inspect each fastener before use and do not use damaged fasteners. |
